TDK Banner
DOCUMENTATION

FEATURES
• Fully adjustable output voltage
• Worldwide input voltages/frequencies
• Full remote control
• Simple parallel operation for upgradeable increased power
• Rep. rates to 1 kHz
• 5kJ/sec peak charge rate
• Compact lightweight design
• Constant charge rate independent of line voltage
• Meets UL, CSA, VDE, safety standard
• Extremely low stored energy
• Protected against open circuit, short circuit, arc, overtemp, over-voltage

APPLICATIONS
• Excimer Lasers
• Pulsed YAG Lasers
• Lithotriptors
• Precipitators
• General Medium Power PFN's
• Grid Bias Supplies
• N2 Lasers
• Dye Lasers
• TEA Lasers

OTHER SOLUTIONS
• LOWER POWER
402
• HIGHER REP RATE
XR802
• HIGHER POWER
LC1202

APP. NOTES
APP Note 500: Calculating Capacitor Charge Time
APP Note 502: Calculating AC Line Currents
APP Note 505: Charging units as Continuous Output DC  Supplies
APP Note 507: Charging Large Load Capacitors
APP Note 509: What is Regulation and Repeatability?
APP Note 513: Power Factor Correction
APP Note 517: Protection Against Voltage Reversal
Appn. Questionnaire
 
802 Series
ALE 802 Series. 1-50 kV, 8000J/sec
802L Capacitor Charging and DC Power Syupply

This series of high voltage switching power supplies is designed to quickly charge capacitors and pulse forming networks in lasers and general modulators. Advanced semiconductor technology combined with high quality construction, yields an exceptionally small and reliable power supply which has set the industry standard for many years.

With many standard features and options, this series is useful in a wide variety of OEM and laboratory applications. Designed for continuous use in severe electrical environments, these air cooled power supplies provide an average charging rate of 8kJ/sec over nine output voltage ranges from 1kV to 50kV, with either positive or negative output polarity. Output control and status monitoring are easily accomplished with the standard remote interface or the optional front panel controls.

Specifications
AC Input
208 VAC or 400 VAC, 3 phase, 50/60 Hz. (Please specify at the time of order).

Average Charging Rate
8000 J/s at rated Output Voltage.

Peak Charging Rate
9000 J/s at rated Output Voltage.

Standard Voltage Ranges
1, 1.5, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50 kV.
All models continuously variable from 0 to 100% of rated voltage output.
Linear to within 1% of full scale.
Accuracy 1% of rated.

Polarity
Available as fixed Positive or Negative, Please Specify.

High Voltage Assembly
Oil Insulated HV section
(Air available on limited models - call factory)

Output Connector/Cable

Output Voltage Connector Cable
1-39kV Proprietary DS 2124
40-50kV Proprietary DS 2214
1-6kV 
(Air Option)
Amphenol HN RG-8/U
Input Connector
VDE, UL, CSA, approved.

Power Factor
Passive PFC 0.85 min

Efficiency
Better than 85%

Stored Energy
Less than 0.3 Joules all models.

Stability
0.2% per hour after 1 hour warm-up.

Pulse to Pulse Repeatability
+/- 0.2% to 1kHz. For higher repetition rates, consult factory

Temperature Coefficient
100 PPM per °C

Ambient Temperature
Storage: -40 to +80 °C
Operating:-0 to +45 °C

Humidity
10-90% Non-condensing

Protection
The power supply is protected against open circuits, short circuits, overloads and arcs.

Agency Approvals
Certification to EN60950 (pending)

Mechanical
19"(482mm) x 17"(432mm) x 7"(178mm)
Weight - 80lbs, 37kg

Click here for mechanical details

Accessories
Detachable 10 foot HV cable
Operating manual

Remote Control
Via 25pin d-type connector on rear panel. Click here for details

Options

Suffix-5V 0 to +5 volt program (0 to full-scale output)
Suffix-LP Latching overload protection
Suffix-EN Low Enable (0V=Enable)
Suffix-CT Optional internal contactor for OEM only (standard on L/S models)
All specifications subject to change without notice.
Ordering Information
802 L/S/OEM - 15kV - NEG - 208VAC - LH
Model     Voltage   Polarity   Input Voltage   Options
 
© Copyright 1999-2010 TDK-Lambda Americas Inc. All rights reserved. Legal Information